About Chandra Archive Proposer Instruments & Calibration Newsletters Data Analysis HelpDesk Calibration Database NASA Archives & Centers Chandra Science Links

HRC-S Event Position Errors Near the Aim Point

HRC-S Event Position Errors Near the Aim Point

Feb 23, 2012

The Problem

In January 2012 it was discovered that because of aim point drift over time, recent observations using the HRC-S (whether using a grating or not) may have a small fraction of source (or 0th order) events that fall on the CRSV=100 tap. (Read here for a short explanation about taps and the degapping process.) The current degap map (hrcsD1999-07-22gaplookupN0002.fits, from 2005/11/16), which converts event positions from RAW to CHIP (which are then converted to DET and TDET, and ultimately to SKY) has residual errors for that tap, leading to asymmetry and broadening of the PSF. It does not affect the positions of events dispersed by the LETG, although the wavelength calibration may be slightly affected (see below). Figures 1-3 show examples from ObsID 13025, a Calibration observation of HZ43 made in March 2011, and one of the worst affected.

   
  Figure 1. 0th order in SKY coordinates. Note that the PSF is extended toward the upper right. Figure 2. 0th order (extracted with 30-pixel-radius circle in SKY coordinates) displayed in CHIP coordinates, showing the dither pattern. The dither pattern on tap CRSV=100 appears fuzzier than elsewhere and there is a significant gap between taps 99 and 100.  


   
  Figure 3. 0th order in SKY coordinates using only events with CRSV=98:99 (left) or CRSV=100 (right). The green circle (5-pixel radius) is centered on the same pixel in each.  

Affected Observations

This problem started to show up in late 2010 as the dither pattern of sources at the aim point began to drift onto CRSV=100. We are aware of 10 GO/GTO observations of point sources that have been affected: ObsID 12154, 12203 (just barely affected), 12332, 12324, 12325, 12401, 12916 (probably negligible), 13184, 13240, and 13651. There is no guarantee, however, that this list is complete. Observers concerned about the source/0th order PSF should check any observation made since the beginning of 2010 following the procedures outlined below. In addition, any observation made since the beginning of the mission that observes a field with multiple or extended sources may be affected.

One way to tell if your observation is affected is to extract an image of the target of interest in SKY coordinates from the Level 2 event file (*evt2.fits) using dmcopy and then display those extracted events in CHIP coordinates using

ds9 "extractedsource.fits[binkey=(chipy,chipx)]" &

This produces an image like that in Figure 2. Any events with CHIPY between 9140 and 9395 fall on the tap with CRSV=100. (Within ds9, with Bin/Binning Parameters/Bin Filter, one can reduce the background and improve image contrast using pi=50:150,pha=0:254. This filtering can, of course, also be applied to the extracted file using dmcopy.)

Another method is to quantify the fraction of events falling on the problematic tap using

dmstat "extractedsource.fits[chipy=9140:9395][cols sky]"

and

dmstat "extractedsource.fits[cols sky]"

Implications and Remedies

Position errors only occur along the long axis of the HRC-S (in detector coordinates RAWY and CHIPY, and grating coordinate TG_R). Because of the roll angle, however, position errors will generally occur in both X and Y SKY coordinates.

An improved degap map for regions near the aim point is currently under development and a calibration observation to map out all of the CRSV=100 tap has been scheduled for April 2012. In the meantime we provide the following recommendations for observers and users.

Future Observations

We anticipate that the revised degap map will be ready in time for all future HRC-S observations, including observations during the remainder of Cycle 13. Cycle 14 proposers should assume that the default aim point (Yoffset=0) can be used without risk. In the unlikely event that the issue is not resolved before the next GO/GTO observation using the HRC-S, User Support Interface scientists will contact observers to help choose an appropriate pointing offset.

Past Observations without a Grating

Timing and event rate studies will be unaffected provided that the source extraction region is enlarged to include misplaced source events. If analysis focuses on source morphology, however, users may want to exclude data from CRSV=100. Level 1 event files can be filtered using

dmcopy "evt1.fits[crsv!=100]" new_evt1.fits

Both Level 1 and Level 2 event files--the latter do not carry the CRSV column--can be filtered using

dmcopy "evt2.fits[chipy=:9139,9396:]" new_evt2.fits

The above filtering yields an event file with good event positions, but does not adjust GTI block data to account for the missing events. This means that light curves, exposure maps, effective areas, etc. will behave strangely and/or no longer be appropriate for the filtered file. Although it is possible to analyze the filtered data and correct for the time-dependent effects of missing events (contact the Helpdesk for assistance), it is strongly recommended that users wait for the new degap map and associated reprocessing instructions before attempting to obtain reliable analysis results.

Past Observations Using the LETG

For most LETG/HRC-S observations, 0th order is of no importance other than centering the spectral extraction regions and defining the origin of the dispersion coordinates. Event position errors for CRSV=100 can lead to a distorted 0th order PSF, which may lead to an error in the centroid used to define the 0th order position. This error could be significant if the user is interested in using the spectrum for accurate line profiles and absolute wavelengths.

For the example in Figures 1-3, the net centroid error is roughly one half pixel. Most affected observations have a smaller fraction of source events with CRSV=100 so centroid errors will be smaller, but a few observations will have larger errors. An error of 1 pixel in centroiding 0th order along the dispersion axis (TG_R) will produce an error of 0.0074 Å in wavelength. The discrepancy between + and - orders will be double this, or 0.0148 Å. For comparison, the FWHM resolution of the LETG is about 0.05 Å. If + and - orders are combined, the resulting summed spectrum will have lines broadened by approximately this amount but their central wavelengths will be unaffected. Centroiding errors in the cross-dispersion direction (TG_D) are believed to be negligible.

If an observer wishes to obtain spectra with the the best possible wavelength calibration he must filter out the CRSV=100 events from the Level 1 event file by following the procedure described above (dmcopy "evt1.fits[crsv!=100]" new_evt1.fits); the remaining data will yield an accurate determination of the 0th order location. The new Level 1 event file can then be reprocessed following the steps in the LETG/HRC-S Grating Spectra thread. Note that using the filtered 0th order data for anything other than anchoring the wavelength scale is not advised; see the caveat in the previous section, "Past Observations without a Grating."


Last modified: 02/23/12



The Chandra X-Ray Center (CXC) is operated for NASA by the Smithsonian Astrophysical Observatory.
60 Garden Street, Cambridge, MA 02138 USA.    Email: cxcweb@head.cfa.harvard.edu
Smithsonian Institution, Copyright © 1998-2004. All rights reserved.